Skip to content
Appliance tips and guides

Oven Repair · 5 min read

How to Check and Calibrate Your Oven Temperature

If the same batch of rolls keeps coming out pale, check how the oven bakes before changing its settings. A repeatable test can tell you whether you need a small temperature adjustment or a repair.

1. Start with a repeatable bake

Check your owner's manual first. Use regular Bake rather than convection for this comparison. If you're testing a double oven, work with one cavity at a time.

  1. Choose a familiar recipe or a package of refrigerated biscuits. Follow its directions for pan type, rack position, temperature and time.
  2. Preheat fully. Center the pan, leave room for air to circulate, and keep the door shut until the first check.
  3. Write down when the food finishes, whether it browns evenly, and the bake mode and rack you used. Repeat the test with the same setup if the result is off.

Whirlpool's biscuit test is one manufacturer's example.

2. Check oven air if your manual allows it

Some manufacturers recommend judging by baking results because a household thermometer may respond too slowly to follow the heat cycle. If your manual allows an air check, use an oven-rated dial or air probe. A food probe inserted in meat measures something different.

  1. Set up while the oven is cold. Clip an oven-rated air probe, such as a compatible thermocouple, near the center of the middle rack. Keep the sensing tip clear of walls, pans and rack metal. The digital reader stays on the counter. Route the cable as its manual directs, away from elements and flames.
  2. Preheat to 350°F in Bake. Follow your manual or the preheat indicator. One Whirlpool model guide gives roughly 12 to 17 minutes, but that's an example, not a timer for every oven. Note when the signal sounds and leave the door closed.
  3. Watch after the beep. Wait until the reader shows the oven cycling steadily. Record readings at regular intervals for about 15 minutes as a starting point, or use the reader's averaging mode if available. If you haven't seen several complete rises and falls, keep watching. Compare the trend with the oven's setting and your bake results.
A separate digital thermometer on the counter beside a closed oven, connected by a thin probe cable
Oven control
350°F setpoint
Counter reader
332°F air reading

Example readings. The oven shows the setting you chose; the digital reader shows what the air probe senses at that moment. A single 332°F reading doesn't mean the oven runs 18°F cold.

AI-generated illustration.

For example, if the oven says 350°F and the counter reader moves from 332°F to 369°F and back, you're seeing a cycle. If readings taken across several cycles average around 330°F and the same test bake repeatedly finishes late, check your manual before changing the offset.

See GE's heat cycling guidance, Whirlpool's example preheat timing and an example counter reader manual.

Watch the oven heat up

Simulated readings

The probe reads the air right now. The average shows where the oven settles across several heat cycles.

An oven connected by a thin cable to a digital reader on the counter
Oven setting
350°F
Live oven air
372°F

Oven air

Average: waiting for more readings

Watching the cycle

Keep the door shut and watch more than one reading.

What would you do next?

3. Adjust only a consistent difference

Find your exact model number and look for Oven Calibration, Temperature Offset or Adjust the Oven Thermostat in its manual. Controls, permitted increments and supported modes vary. Note the original setting before you change it.

If the manual supports an offset and the tests consistently show the oven is cool, choose a small allowed adjustment in the warmer direction. If it runs hot, go cooler. Save the setting as directed and repeat the same bake. The temperature displayed during baking may still show the original setpoint on some models.

Compare Whirlpool's calibration controls and GE's knob and keypad example. Use the directions for your model.

One reading at 330°F on a 350°F setting
No adjustment yet. You may have caught the bottom of a normal heat cycle.
Two test bakes finish late, and oven air consistently averages low
Check whether your model supports a positive bake offset. Start with a small allowed step and test again.
Back of the tray burns while the front stays pale
Check rack position, pan placement and bake mode. If it repeats, have the oven diagnosed. An offset changes the overall temperature, not the hot spot.

When to call for service

Call if preheat never finishes, the door won't seal, the temperature changes unpredictably, or a small offset doesn't help. Stop using the oven if it sparks, smells like burning electrical parts, or repeatedly trips a breaker. Calibration doesn't fix those problems.

Send the model number, the mode and cavity you tested, and what happened to the food. If you logged readings, include where the probe sat and when you read it.

Join our newsletter

Sign up and you get a chance to win a free service call. We draw one subscriber every month, and the winner also gets a bonus prize. About one email a month, and you can unsubscribe any time.

No purchase necessary. Open to Sonoma, Marin and Napa county residents, 18 or older.